Certificates
Technical request
Contact

10 GM - reels

Due to a structured modular principle, our GM reels with smooth flanges and diameters up to 630 mm allow the greatest possible variety of dimension variants and application possibilities as dispatch or process reels.

REEL DESIGNATIONS

GM reels have the same basic dimensions as those in the VM series, however, the flanges have no ribs on the outside surfaces. The outer surfaces of the flanges are roughened in a star formation and can be used as contact surfaces for braking purposes.

OUTER WIDTH

The outer width of the reels is normally the winding width (L2) plus 2x the flange thickness (S). If desired, however, in conjunction with smaller central bores hub extensions can also be supplied, which then additionally increase the overall width of the reels.

TOLERANCES

All dimensions, weights and loads stated are approximate values; tolerances and deviations which are customary for the industry remain reserved.

IMPORTANT

Shrink-wrapped pallets of packages must not be stored in direct sunlight, as the heat build-up may cause the plastic to warp.

CENTRAL BORES

The reels have a standard central bore of 127 mm (5 inch) in diameter. Smaller diameters of any size can also be supplied by means of additional inserts. For various reasons, it has proven to be best to use bore dimensions which are already used in the relevant standards, e.g. 36 and 56 mm. All bores are fitted with a supporting tube. The bores can also be fitted with a polyamide bush, which increases the abrasion resistance of the central bore. These bushes can be replaced.

DRIVES

Bores or pins are available on request.

SPECIAL REQUESTS

All reels with a barrel diameter d2 >= 200 mm can be bolted for additional strength. This brochure can only provide a guide to our products and standard dimensions, as numerous combinations and details are possible. If possible, please enclose a drawing with your enquiry, showing the position and design of drive devices and wire entry and exit. A wide range of different hub designs are also possible; therefore please contact us if you have any special requests.

Material

ABS (acrylonitrile-butadiene-styrene) in the colour grey. Other colours are also available subject to certain minimum quantities.

Winding widths

The winding widths given in the table are the most cost-effective. Smaller winding widths can also be supplied by shortening the barrel.

Material Information
Designation Flange Ø Barrel Ø Central bore Ø Width Winding width Flange thickness Winding-
volume
Central bore Ø
tapered part
Drive-
hole/pin
Drive-
distance
d1 [mm] d2 [mm] d3 [mm] L1 [mm] L2 [mm] S [mm] V [cm³] d4 [mm] d5 [mm] E1 [mm]
Reel  GM 315/127-284
Reel  GM 315/127-284 Reel GM 315/127-284
315 160 16 - 127 284 50 - 250 17 2891 - 14456 143.5
Reel  GM 355/127-314
Reel  GM 355/127-314 Reel GM 355/127-314
355 180 16 - 127 314 50 - 280 17 3677 - 20589 143.5
Reel  GM 355/127-344
Reel  GM 355/127-344 Reel GM 355/127-344
355 224 16 - 127 344 50 - 310 17 2979 - 18467 143.5
Reel  GM 400/127-286
Reel  GM 400/127-286 Reel GM 400/127-286
400 160 16 - 127 286 50 - 250 18 5278 - 26389 143.5
Reel GM 400/127-316 400 180 16 - 127 316 50 - 280 18 5011 - 28061 143.5
Reel  GM 400/127-321
Reel  GM 400/127-321 Reel GM 400/127-321
400 200 16 - 127 321 50 - 285 18 4712 - 26861 143.5
Reel  GM 450/127-316
Reel  GM 450/127-316 Reel GM 450/127-316
450 180 16 - 127 316 50 - 280 18 6680 - 37407 143.5
Reel GM 450/127-321 450 200 16 - 127 321 50 - 285 18 6381 - 36374 143.5
Reel  GM 450/127-346
Reel  GM 450/127-346 Reel GM 450/127-346
450 224 16 - 127 346 50 - 310 18 5982 - 37087 143.5
Reel  GM 500/127-325
Reel  GM 500/127-325 Reel GM 500/127-325
500 200 16 - 127 325 50 - 285 20 8247 - 47006 143.5
Reel  GM 500/127-355
Reel  GM 500/127-355 Reel GM 500/127-355
500 250 16 - 127 355 50 - 315 20 7363 - 46388 143.5
Reel  GM 500/127-370
Reel  GM 500/127-370 Reel GM 500/127-370
500 280 16 - 127 370 50 - 375 20 6739 - 50540 143.5
Reel  GMV 500/51-315
Reel  GMV 500/51-315 Reel GMV 500/51-315
500 250 51 315 50 - 315 27.5 7363 - 46388
Reel GMV 500/56-375 500 250 16 - 56 375 50 - 315 27.5 7363 - 46388
Reel  GMV 500/127-370
Reel  GMV 500/127-370 Reel GMV 500/127-370
500 250 16 - 127 370 50 - 315 27.5 7363 - 46388 143.5
Reel  GM 560/127-425
Reel  GM 560/127-425 Reel GM 560/127-425
560 280 16 - 127 425 50 - 375 25 9236 - 69272 143.5
Reel  GMV 610/127-355
Reel  GMV 610/127-355 Reel GMV 610/127-355
610 250 127 355 305 25.4 74163
Reel  GMV 610/127-355
Reel  GMV 610/127-355 Reel GMV 610/127-355
610 355 127 355 305 25.4 58946
Reel  GM 630/127-430
Reel  GM 630/127-430 Reel GM 630/127-430
630 315 16 - 127 430 50 - 425 25 11690 - 99362 143.5

Technical drawing

Spools

Our Certification

Our quality management system has been ISO 9001-certified since 1997, and our environmental management system has been ISO 14001-certified since 1999. In October 2012, our energy management system was certified in accordance with DIN EN ISO 50001.